Convert Solid into a Shell
- Danny
- Topic Author
- Offline
- New Member
Less
More
- Posts: 3
- Thank you received: 0
8 years 11 months ago #8044
by Danny
Convert Solid into a Shell was created by Danny
Hello,
i am new in use Salome.
My Problem is, that i must convert a solid into a shell. Is this possible in Salome or in another open source program?
The solid is ja .step file.
Thank you for your answer.
Grettings
i am new in use Salome.
My Problem is, that i must convert a solid into a shell. Is this possible in Salome or in another open source program?
The solid is ja .step file.
Thank you for your answer.
Grettings
Please Log in or Create an account to join the conversation.
- Claus
- Offline
- Moderator
Less
More
- Posts: 670
- Thank you received: 34
8 years 11 months ago #8045
by Claus
Code_Aster release : STA11.4 on OpenSUSE 12.3 64 bits - EDF/Intel version
Replied by Claus on topic Re: Convert Solid into a Shell
Salomé would be a good bet to explode the model into faces and recombining them.
/C
/C
Code_Aster release : STA11.4 on OpenSUSE 12.3 64 bits - EDF/Intel version
Please Log in or Create an account to join the conversation.
- RichardS
- Offline
- Elite Member
8 years 11 months ago #8047
by RichardS
SimScale - Engineering Simulation in your browser!
Replied by RichardS on topic Re: Convert Solid into a Shell
Hello,
I think's it's rather about mid-surface creation .
To my knowledge this is not possible with Salome or any other open-source cad tool
- But if there is one, i would also be very interested to hear about it!
Bets regards,
Richard
I think's it's rather about mid-surface creation .
To my knowledge this is not possible with Salome or any other open-source cad tool
- But if there is one, i would also be very interested to hear about it!
Bets regards,
Richard
SimScale - Engineering Simulation in your browser!
Please Log in or Create an account to join the conversation.
- Claus
- Offline
- Moderator
Less
More
- Posts: 670
- Thank you received: 34
8 years 11 months ago #8048
by Claus
Ah, you might be right. I'd be interested in hearing about it too.
/C
Code_Aster release : STA11.4 on OpenSUSE 12.3 64 bits - EDF/Intel version
Replied by Claus on topic Re: Convert Solid into a Shell
RichardS wrote: Hello,
I think's it's rather about mid-surface creation .
To my knowledge this is not possible with Salome or any other open-source cad tool
- But if there is one, i would also be very interested to hear about it!
Bets regards,
Richard
Ah, you might be right. I'd be interested in hearing about it too.
/C
Code_Aster release : STA11.4 on OpenSUSE 12.3 64 bits - EDF/Intel version
Please Log in or Create an account to join the conversation.
- Danny
- Topic Author
- Offline
- New Member
Less
More
- Posts: 3
- Thank you received: 0
8 years 11 months ago #8050
by Danny
Replied by Danny on topic Re: Convert Solid into a Shell
Thank you for your answers.
Which programms do you use to create a Shell from a solid?
Is there no way to do this with open source?
Which programms do you use to create a Shell from a solid?
Is there no way to do this with open source?
Please Log in or Create an account to join the conversation.
Moderators: catux
Time to create page: 0.130 seconds