copy error

hello, i am getting the following copy error when trying to do an analysis. i've poked around searching the forums and don't think my issue is the same as what i discovered since my UNITE is 80.

[code:1]

---

Copying results

copying .../fort.8 [ OK ]
copying .../fort.6 [ OK ]
copying .../fort.80 [FAILED]
Exit code : 1
cp: cannot stat `fort.80': No such file or directory


<E>_COPY_ERROR error during copying fort.80 to /home/dmcdaniel/FixedVane/Cas.resu.med
message : cp: cannot stat `fort.80': No such file or directory



<F>_ERROR Code_Aster run ended
[/code:1]

my command file contains these lines that may dictate the "UNITE" keyword effecting this copy error.

[code:1]MAIL=LIRE_MAILLAGE(FORMAT='MED',);

IMPR_RESU(FORMAT='MED',
UNITE=80,
RESU=_F(MAILLAGE=MAIL,
RESULTAT=RESU,
NOM_CHAM=('SIGM_NOEU_DEPL','EQUI_NOEU_SIGM','DEPL',),),);[/code:1]

other stuff that may be relevant:
[code:1]

---

--- DIAGNOSTIC JOB : <F>_ERROR

---

EXIT_CODE=4
P actions make_etude
P consbtc oui
P debug nodebug
P mclient opteron
P memjob 2048000
P mode interactif
P ncpus 1
P noeud opteron
P nomjob Cas
P origine ASTK 1.6.2
P serveur opteron
P soumbtc oui
P uclient dmcdaniel
P username dmcdaniel
P version STA9.4
P xterm /usr/bin/xterm -sb -si -geometry 90x32 -display :1006
A ORBInitRef NameService=corbaname::opteron:2813
A args
A memjeveux 500
A tpmax 5000
F comm /home/dmcdaniel/FixedVane/scav1Rot.comm D 1
F med /home/dmcdaniel/FixedVane/scav1Rot.mail.med D 20
R base /home/dmcdaniel/FixedVane/Cas.base RC 0
F resu /home/dmcdaniel/FixedVane/Cas.resu R 8
F mess /home/dmcdaniel/FixedVane/Cas.mess R 6
F med /home/dmcdaniel/FixedVane/Cas.resu.med R 80 [/code:1]

many thanks for any help with this.

thanks for your comment Kees.

i didn't create a results file, my assumption was that aster would do so for me; is that correct?

anyhow, i was able to get it to work using aster 10 that i had already installed in 64 bit before installing salome meca.

for now i will continue to use that, using ASTK 1.8; although that doesn't work if the "follow-up" box is checked.

are there any good instructions for ASTK, detailing all the necessary file types as well as as_run command line parameters?

thanks again

Hi, I'm an Eng student and am trying to do some FEA analysis using Aster through Salome-MECA (I'm on CAELinux 2010) but I'm a complete noob to CAELinux.

I'm attempting to run a Linear Analysis through code-aster but keep getting a error of:


DIAGNOSTIC JOB : <F>_COPY_ERROR


Looking back through the flasheur file I see that another error precedes the copy error:


JDC.py : ERREUR A L'EXECUTION - INTERRUPTION
>> JDC.py : DEBUT RAPPORT
CR d'execution de JDC en MIXTE
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
! <S> Exception utilisateur levee mais pas interceptee. !
! Les bases sont fermees. !
! error : <EXCEPTION LEVEE> FACTOR_20 !
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
fin CR d'execution de JDC en MIXTE

>> JDC.py : FIN RAPPORT
EXECUTION_CODE_ASTER_EXIT_7746=1
<INFO> Code_Aster run ended, diagnostic : <S>_ERROR


I've looked through the CAELinux and Code-Aster forums but couldn't see a similar issue. Could anyone shed some light on this problem?
Please let me know if you need more information.