adaption of *.comm-files to aster 9.0

Hi,

Joel Cugnoni has provided complete template-projects (plasticity, contact etc.) ,that are VERY useful as basis for getting familiar with Code_Aster and Salome. For a number of reasons I had to shift from PCLinuxOS to SUSE 10.1 and I have migrated or installed/compiled Salome and Code_Aster Version 9.0 to this OS. Now, Joel's templates produce errors when run with COD_Aster 9.0. From the Code_Aster forum I learned that some of the key words are no more valid or have to be extended under Version 9.0.

With the obtained advice I could get the respective *comm-files syntactically correct, but when run with Code_Aster 9.0 they produced other errors and/or warnings. My knowledge is so far still too limited to figure out what could be the problem.

Has somebody already updated Joel's CAELinux-tutorial files or is about to do it? I would be very grateful if I could get them too.

Thanks,

Walter

Hello Joel,

here comes the feed-back for some of the templates. I havn't done all yet. In the 'thermomeca'-example I've changed the following:

thermomeca
=============
THmodel=AFFE_MODELE(MAILLAGE=MeshLin,
AFFE=_F(TOUT='OUI',
PHENOMENE='THERMIQUE',
MODELISATION='3D',),);

MeshLin=MODI_MAILLAGE(reuse =MeshLin,
MAILLAGE=MeshLin,
ORIE_PEAU_3D=_F(GROUP_MA=('topF1','topF2','backF1',
'backF2','botF1','botF2',),),);

#### MODELE=THmodel,);
#### The above part had to be removed due to error
#### message already
#### in eficas: No such key-word 'MODELE' available. #### Walter, 13.01.2007


My comments start with 4 hash-symbols. After this change, the command file was executed without warning- or error-messages

//////////////////////////////////////////////////////////

plasticity
============

I changed/added keywords in the command-file according to
the advice from the Code_Aster-forum. Then, Eficas didn't complain any more but the following error-message was issued at run-time and the execution was aborted:


!

---

!
! !
! !
! !
! le group_ma : symmY existe deja. !
! !
! !
! Ceci est une alarme. Si vous ne comprenez pas le sens de cette !
! alarme, vous pouvez obtenir des r�ultats inattendus ! !
!

---

!


!

---

!
! !
! !
! !
! LE NOM DEMANDE EXISTE DEJA DANS LE REPERTOIRE MeshQuad.GROUPEMA !
! !
! !
! Cette erreur est fatale. Le code s'arrete. !
!

---

!


Code_Aster run ended, diagnostic : _ERROR

_CORE_FILE Code_Aster run created a coredump

There were following-up errors produced, but I think they don't matter. I'm attaching \"my\" plasticity-command file, my comments are again marked by 4 hash-symbols


///////////////////////////////////////////////////////////

contact
=======

A few changes according to the Forum-advice, see attached command-file (4 hashes).

At the beginning of the execution the following warnings were issued:

! !
! !
! les variables de commandes initiales induisent des contraintes incompatibles !
! !
! !
! Ceci est une alarme. Si vous ne comprenez pas le sens de cette !
! alarme, vous pouvez obtenir des r�ultats inattendus ! !
!

---

!

| 1 X | 3.93220E-02 X | 3.76892E+03 |TANGENTE | 62 X | ALGO. | 0.00000E0 |

!

---

!
! !
! !
! !
! les variables de commandes initiales induisent des contraintes incompatibles !
! !
! !
! Ceci est une alarme. Si vous ne comprenez pas le sens de cette !
! alarme, vous pouvez obtenir des r�ultats inattendus ! !
!

---

!

... ... ...

!

---

!
! !
! !
! Plus de 5 fois le meme message d'alarme. !
! !
! Ceci est une alarme. Si vous ne comprenez pas le sens de cette !
! alarme, vous pouvez obtenir des r�ultats inattendus ! !
!

---

!

.... ....

FERMETURE DE LA BASE \"GLOBALE\" EFFECTUEE.
ARRET NORMAL DANS \"FIN\" PAR APPEL A \"JEFINI\".
FERMETURE DES BASES EFFECTUEE

DIAGNOSTIC JOB : _ALARM

The job was completed and results were produced, but I'm wondering whether they can be trusted.

So far for tonight. I hope it helps for the conversion to Aster 9.0

Regards,

Walter

Hello Joel,

my attached ascii-files have not been accepted. So
I'm trying again with zipped command-files of the plasticity and contact-examples.

Walter

... now the contact file ...

Hi to all.

The files in this thread seems corrupted. It's impossible to download it.

Many many Thanx

Andrea